BMR Gen 2 B58 Catch Can Kit

The Black Market B58 Gen 2 Catch Can

Check out our new FULLY BILLET B58TU Catch can that features PCV Ventilation from the oil cap!

Looking For Gen1? Find it Here

This kit is ready to run, it includes all fittings, hoses, and hardware needed to install.

READ BEFORE ORDERING

Current Lead Time is approximately 1.5 weeks before shipping.
We now have fitment options for G series BMW!

Our new options for fitment determine one of two mounting locations for the catch can. If you select stock / hybrid turbo then you will receive a mounting bracket and lines that mount the catch can on the strut tower behind the airbox.

All top mount turbo catch cans mount below the front radiator support.

Any B58 that is tuned will eventually suffer from excessive crank case pressure. Most people choose to vent the oil cap with a filter to remedy this, which can leave a big mess and looks pretty awful. Our B58 Catch can routes a braided AN hose from our custom billet oil cap to the catch can all while staying UNDER the engine cover!

 All of our catch cans are packed with stainless steel and internally baffled to catch oil particles before filtering and venting to atmosphere.

All catch cans include an M12 X 1.5 drain bolt on the bottom of the catch can for easy service.

Our B58 catch can also includes pre made AN lines to vent PCV, and CCV. In high boost applications (Past 30psi) The CCV Should be capped off with included -6AN caps.

The black market race B58 Catch can was designed to be a universal kit that can be configured for any PCV venting configuration. It includes -6AN plugs if you choose to only vent the oil cap and the PCV.

This kit can also be purchased without the oil cap, venting ONLY CCV and PCV.

Oil cap vents can be purchased later as an upgrade!

IMPORTANT!
Past 30PSI PCV pins are mandatory to prevent valve cover failure. When installing PCV pins the CCV port on the side of the block should also be capped off as its OEM Function to draw air into the motor no longer functions with PCV pins installed. Leaving it uncapped can cause excessive oil to build up in your catch can.

If you are ordering for a stock / hybrid turbo car but want to upgrade to top mount in the future a conversion kit can be ordered for $80 which includes: Hoses, AN Fittings, and Mounting bracket. Please email blackmarketrace@gmail.com for this option.

Current lead time is approximately 1.5 weeks to ship!

we make everything in house to order, we appreciate your patience! 

Raw catch cans typically ship faster as we have been backed up on powder coat. 

Fits: 

• Toyota Supra 3.0
• 2020+ G30 540i
• G12 740i
• G15 840i
• G05 X5 40i
• G06 X6 40i
• G42 M240i
• G20 M340i
• G22 M440i
• G29 Z4 M40i
• X3 M40i
• X4 M40i 

DISCLAIMER

For Off-Road or Closed-Course Use Only

This product is designed and intended solely for use on vehicles participating in off-road or closed-course racing events. It is not legal for sale or use on any pollution-controlled motor vehicles in the state of California. By purchasing this product, the buyer acknowledges and agrees that the product will not be used in any manner that violates local, state, or federal emissions regulations.

Notice to California Residents:

The sale or use of this product on any vehicle registered for highway use in California is strictly prohibited. This product does not comply with the California Air Resources Board (CARB) emissions standards. Any attempt to use this product on public roads may result in fines and penalties, and the buyer assumes all responsibility for compliance with applicable laws.

Important:

Installation and use of this product on a pollution-controlled vehicle is a violation of federal and state laws and may be subject to fines and penalties. This product is sold for off-road or closed-course use only, and the manufacturer, distributor, and retailer are not responsible for any misuse or non-compliance.